•  
     
     
     英翻中翻譯樣本

    Repair Method

    I. From inside the riding surface of the slide, take the razor knife and cut into the leaking joint.

    Remove the old sealant that has lost its elasticity.

    II. Take a clean rag or cloth with acetone and apply to the joint. This will clear all remaining

    dirt, debris, and water from the old sealant.

    III. Apply new sealant in the area where sealant has been removed. Using the putty knife, work

    the sealant into the joint to ensure that the sealant has fully covered the void.

    IV. Remove excess sealant with the putty knife, and wipe the joint clean with a clean cloth and

    acetone. Use the acetone sparingly as using too much can deteriorate the remaining

    sealant.

    V. Allow up to twenty four hours for the sealant to properly cure. If this is not possible, allow as

    much time as possible.

    修補方法

    I.取一把剃刀,從滑道滑行面里面開始切進泄漏接合處。清除掉已經喪失彈性的密封劑。

    II.拿一塊干凈的抹布或蘸有丙酮的布擦拭接合處。這可以把老化密封劑上殘留的灰塵、碎片和水全部清理掉。

    III.在清理掉老化密封劑的地方涂上新的密封劑。用油灰刀把密封劑填入接合處,確保密封劑全部蓋住空洞。

    IV.用油灰刀清理掉多余的密封劑,用干凈的布和丙酮擦干凈接合處。丙酮盡量少用,因為過多的丙酮可能會使余下的密封劑老化。

    V.  讓密封劑留置長達24小時的時間,以待完全固化。如果不可能達到這一時間,也要盡可能留置更長的時間。

     



    中譯英翻譯樣本

        四. B級金庫門基本參數及技術條件

        IV. Basic parameters and technical conditions of the Class B vault door

        1.產品必須符合國家公共行業標準GA/T143-1996金庫門中的B級門和國家金融行業標準《JR/T0001-2000》金庫門中的2級門和《JR/T0002-2000》組合鎖中的1類鎖標準。

        i. Products must comply with the requirements of Class B vault door specified in GA / T143-1996 of the National Public Industry Standards as well as requirements of Class 2 vault door specified in JR / T0001-2000 and Class 1 combination lock specified in JR / T0002-2000 of the National Financial Industry Standards.

        2.B級金庫門的基本結構為門框、門扇、日閘門、數字機械密碼鎖、專用鎖。

        ii. The Class B vault door basically consists of the frame, leaf, day gate, digital mechanical cipher lock and special lock.

        3.金庫門的門框、門扇正面四周周邊間隙不大于1mm,不應有可以直接窺視到門內的縫隙,門框、門扇的表面平整,外表面的平面度不大于2 mm,內表面的平面度不大于4 mm。

        iii. The front peripheral clearances of the vault door’s frame and leaf shall not exceed1mm, and there shall be no gap from which the inside of the door can be directly peeped, the surface of the frame and leaf shall be smooth with a flatness of the outer surface not more than2 mmand that of the inner surface not more than4 mm.



    EPB系列工程塑料軸承采用高性能的工程塑料為基料,通過高分子材料改性技術在其內部植入高強度纖維和特種固體潤滑脂改善了綜合耐磨性能; 高強度纖維網狀結構加強了材料的強度,特種固體潤滑脂的復合使得EPB系列工程塑料軸承具有極好的自潤滑性能和耐磨性能。

        The overall wear resistance of the series of EPB engineering plastic bearings is improved by use of high-performance engineering plastic as principal raw material into which high-strength fiber and special solid lubricant are placed by means of modification of polymer materials; the net structure of the fiber can increase the principal raw material’s strength, while the composition of the lubricant gives the series of EPB excellent self-lubricating and wear-resisting properties. 
    無論是耐久性要求很高的汽車工業、高速應用、水下應用、高溫和抗腐蝕應用或是要求符合FDA標準的食品工業CSB總能為客戶提供不同的解決方案。

        Whether for automobile industry in need of high durability, or for applications under conditions such as high speed, underwater, high temperature and corrosion, or for food industry required to meet standards of FDA, CSB always can provide customers with individual solutions. 

    此類軸承作為最廣泛的自潤滑塑料軸承被應用;EPB塑料軸承作為通用性最強的代表可以滿足使用溫度80℃以下的很多場合;EPB3工程塑料軸承無論是軸承載荷還是使用溫度方面均具備很強的通用性;EPB7以及EPB13作為耐磨性要求較高但對軸承性價比要求不高的被推薦;EPB19是通用性軸承中耐溫最高可在150℃下長期使用,耐磨性同樣出色的材料。

        Such bearings are most widely applied as self-lubricating plastic bearings; with the highest universality, the EFB plastic bearing can be used in many occasions when the operating temperature is at 80℃ or below; EPB3 features high universality whether from load or operating temperature; EPB7 and EPB13 are both recommended to be used in occasions in need of good wear resistance but in no need of high cost-performance; among versatile bearings, besides a good wear resistance, EPB19 features the highest resistance to temperature so that it can be used even at high temperature of 150℃ for a long time.   



    ● 自潤滑免維護塑料直線軸承。無噪音運行。適合在極其惡劣的粉塵環境中連續使用。允許被食品藥品包裝機械清洗液清洗。
    ● 免維護、長期干運行、無噪音;
    ● 適合灰塵中長期運行;
    ● 耐腐蝕,適合用消毒液清洗;
    ● 斜槽設計更強的對軸保護能力;
    ● 減小了槽寬以增強承載能力;

        ● A maintenance-free self-lubricating plastic linear bearing. Noiseless. Appropriate for continuous use in extremely severe dusty environment. Permitted to be cleaned with the cleaning solution for food & drug packaging machinery.

        ●Maintenance-free, suitable for long-term dry running, and noiseless;

        ●Suitable for use in dusty environment for a long time;

        ● Corrosion-resistant, suitable for being cleaned with disinfectant;

        ● Because of the design of skewed slot, the series boasts stronger protection for shaft;

    ● The skewed slot is narrowed for an enhanced carrying capacity; 

     
     
     
    Power by 東和翻譯公司 版權所有 備案號:粵ICP備15013681號 html地圖 | xml地圖 SEO技術支持:西安點創科技
    欧美高清无码乱妇96在线观看-日本毛片免费视频观看-人人妻人人爽人人澡